Design of RCC Structures notes | PDF Free Download

Objective of Design of RCC Structures:

  • To Design simple RCC Structures.
  • To Use limit state of design for beam, slab, staircase, column, and  footings.
  • To Perform detailing of various Recistructures.

Limitation of plain concrete.

Plain cement concrete is a hardened mass obtained from  a mixture of cement, sand, gravel& water in definite proportions. The major limitations of the plain concrete are;

  • Concrete is brittle material
  • It has Low Tensile strength
  • Concrete has low toughness & specific strength
  • Formwork is required & long curing time
  • Working with cracks
  • Need strict Quality control
  • Concrete is less-ductile
  •  Weight of concrete & high compared to its strength

Reinforced Cement Concrete

Plain cement concrete has very low tensile strength. To improve tensile strength of concrete, some sort of reinforcement is needed which can take up the tensile stresses developed in the structure. Thus, reinforced cement concrete is a composite materials which is made up of concrete & steel reinforcement.

The composite action of steel & concrete depend on,

  • Bond between steel & Concrete.
  • Prevention of corrosion of steel bar embedded in concrete.
  • Practically equal thermal expansion of concrete & steel.

Advantages of RCC over other construction material

  • Good strength in tension as well as compression.
  • Durable if designed & load properly. (last upto 100 years).
  • RCC section can be given any shape easily by properly designing the formwork. Thus, It is more suitable for architectural requirements.
  • The steel reinforcement imports ductility to RCC structure
  • RCC is cheaper as compared to steel & prestressed concrete.
  • Raw materials for RCC are easily available & can be transported easily.
  • More fire resistance.
  • Almost impermeable to moisture.
  • Properly designed RCC structures are extremely resistant to earthquakes.

Disadvantages of RCC structures

  • RCC structures are heavier than other structures.
  • RCC needs a lot of formwork, centering, & shuttering to be fixed, thus requiring a lot of site space & skilled labour.
  • Concrete takes time to attain its full strength. Thus RCC structures can’t be used immediately after construction, unlike steel structures.
  • They require high initial cost for construction.
  • All the constituents of RCC are not locally available everywhere. At the end of usefullife, Structures need to be dismantled.

Properties of Concrete

The properties of concrete depends upon the proportions & type of its ingredients. A properly redesigned concrete mix is very durable. A good concrete mix should satisfy following  requirements.

  • The concrete should be mixed throughly to form homogeneous mixture
  • It  Should be compacted properly.
  • It should be sufficiently  cured to get full strength
  • W/C ratic should be appropriate considering strength and workability criteria
  • Concrete mix should be designed properly & should have all Ingredients in right
  • proportions.
  • Water used should be free from all harmful organic substances.
  • Aggregate should be hard, durable & properly graded For most RCC works,  20 mm size of
  • aggregate is suitable.
  • Cement used for RCC work should be of good quality of measure by weight only not by volume.

Notes*

For RCC works  grade of concrete should be higher than  M20 .

For  Post Tensioning works  grade of concrete should be higher than  M35.

For  Prestressed works  grade of concrete should be higher than  M40.

Properties of Reinforcement

  1. It should have high tensile strength
  2. It should be cheap, easily available & durable.
  3.  It should be workable, easy to cut, bend & join.
  4. It should not react with other ingredients of RCC.   
  5.  It should be free from loose mill scales, loose rust etc.

Read more in Design of RCC Structures notes pdf below. You can download it.

What will you get in Design of RCC Structures notes pdf?

Design of RCC Structures notes | PDF Free Download

Table of Contents for “Design of RCC Structures”

1.Introduction

  • Limitation of Plain Concrete
  • Properties of Reinforcement and Concrete
  • Analysis of Forces and Stresses

2. Design Methods

  • Working Stress Method
  • Ultimate Load Method
  • Limit State Method
    • Limit State of Collapse
    • Limit State of Serviceability

3. Limit State Design for Beams and Slabs

  • General Design Considerations
  • Analysis of Singly and Doubly Reinforced Beam Sections
  • Analysis and Design of Flanged Beam Section
  • Strength and Serviceability for Flexural Members
  • Design and Detailing of Beams (Flexure, Shear, Torsion)

4. Design of Slabs

  • One-Way Slabs
  • Two-Way Slabs
  • Reinforcement Detailing for Slabs
  • Shear, Deflection, and Development Length Checks

5. Limit State Design for Columns and Footings

  • Design Considerations for Short/Slender Columns
  • Design and Detailing of Circular Columns
  • Axially Loaded Columns
  • Biaxial Bending and Compression
  • Design of Slender (Long) Columns

6. Design for Torsion

7. Important Clips from IS 456:2000

  • Nominal Cover and Bar Diameter
  • Concrete Exposure Classes

·  Appendices

  • Sample Design Calculations
  • Charts and Tables from IS 456:2000

Read Also,

Concrete technology Handwritten notes pdf

Structural analysis notes | PDF Free Download

Estimation and Costing Handwritten notes pdf

Complete Bar Bending Schedule for Different Structure (Free e-Book)

Share On:

"Structural Engineer" with over 5 years of proven expertise in estimation, structural design, and surveying. I specialize in creating safe, efficient, and sustainable structures that combine innovation with practicality.